Diy DIY – Springfield Hellcat Trigger Job Iain Harrison August 11, 2020 1 Comments, Join the Conversation The Hellcat has been one of Springfield’s most successful product introductions, easily outstripping supply and making it a hot ticket item in the micro-9 segment. It’s ability to shoehorn 13+1 rounds into a tiny package has given its main rival, the SIG P365 a run for its money, but there’s one area in which the petite pistola loses out. And that’s its trigger. So it's time for a Springfield Hellcat trigger job. Our sample originally tripped the gauge at a healthy 7.25 pounds with a certain amount of grittiness before the break and being trigger snobs, that didn’t cut it. Enter the guys at Apex Tactical, who fortunately live just down the road from the editorial compound. With their newest trigger kit in our sweaty paws, we hastened to the workbench to give the Hellcat a trigger job. The whole process takes less than half an hour, and results in a smooth rollover break, right at about 5.5 pounds. If you’re looking to improve your own trigger, here’s how. You'll need a few basic tools, such as a bench block, 1/16 inch punch and hammer, Dremel, felt bob and polishing compound. 1. Field strip the handgun and using a 1/16 inch punch and bench block, drive out all three pins. The three action pins should press out easily. Note their locations, denoted by the number of grooves 2. Lift out the locking block and wiggle out the takedown lever and spring. Hellcat locking block removal. 3. Remove the slide lock lever and sear housing, along with the mag blocking lever. 4. Remove the trigger bar from the sear housing by pulling up and forward to disengage from the slots. Once you have the trigger bar free, use your punch to drive out the pin connecting it to the trigger. 5. Replace the trigger with the one from the APEX kit, using the instruction card as a spacer between the trigger bar and the trigger slot. If you don’t use a spacer, you could wind up collapsing the slot, causing it to drag on the bar – not good. 6. Remove the sear from the sear housing by pushing out the retaining pin. Separate the sear spring from the sear using a pair of needle nose pliers, and replace it with the new one. 7. Using your trust Dremel and a felt bob with a little polishing compound, polish the sear engagement surfaces to a mirror finish, then replace the sear along with its new spring back into the sear housing. While you have it in hand, polish the top of the trigger bar where it makes contact with the safety plunger in the slide. Use your Dremel to polish the sear engagement surfaces. 8. Place the trigger bar back into the sear housing and replace the whole shebang back into the frame, along with the mag blocking bar. Use the instruction card that came with the trigger kit to take up space between the trigger and trigger bar. 9. Reinsert the locking block and slide lock lever, then replace the action pins. That’s it for the frame portion of the trigger job – now on to the slide. The Springfield Hellcat extractor assembly is under tension. Be careful as you slide the backplate off, or you'll be chasing it across the room. Takedown tab is just below the rear sight. 10. Remove the backing plate by pressing in the little tab at the top, then sliding it down. Be careful as the striker and extractor are under spring tension. 11. Remove the striker and extractor assemblies, then the safety plunger. 12. Remove the striker spring by pressing it down on the striker, then separate the two halves of the split collar.13. Polish the striker tail where it contacts the sear, then install the new spring by compressing it and reinstalling the split collar.14. Polish the safety plunger, then reinstall it, along with the striker, extractor spring and backplate. 15. Reassemble the pistol, function check and you’re done! When looking to upgrade your handgun, it's a harsh debate between sights and the trigger as the recommended first choice. Thankfully Apex as tackled so many common handguns that they keep the argument going. It's no black magic to replace the trigger, and it doesn't make anyone a better shooter, but there's something to be said about making small improvements, so long as there's practice to match. A Springfield Hellcat trigger job boosts the appeal of this contender in the sub compact market. More from Springfield: Check out our article on the Hellcat in Concealment 16. For a full Review of the Hellcat, check out. Read more about the XDM Elite Series. Springfield announces the XDM Elite 3.8, read the press release. Springfield Hellcat RDP Review: Even better with 15-round mags. Explore RECOILweb:RECOIL Magazine Issue 46The Midwest Industries Aimpoint Mount - it's Inbound[SHOT Show 2017] Media Day at the Range - SHOT Show 2017 Constant CoverageRECOILtv Gun Room Video: Mid America Armament Rapid Take Down Kit NEXT STEP: Download Your Free Target Pack from RECOILFor years, RECOIL magazine has treated its readers to a full-size (sometimes full color!) shooting target tucked into each big issue. Now we've compiled over 50 of our most popular targets into this one digital PDF download. From handgun drills to AR-15 practice, these 50+ targets have you covered. Print off as many as you like (ammo not included). Get your pack of 50 Print-at-Home targets when you subscribe to the RECOIL email newsletter. We'll send you weekly updates on guns, gear, industry news, and special offers from leading manufacturers - your guide to the firearms lifestyle.You want this. Trust Us.