Guns Custom Hi Power MK3 Iain Harrison March 6, 2019 2 Comments, Join the Conversation At RECOIL, we review every product fairly and without bias. Making a purchase through one of our links may earn us a small commission, and helps support independent gun reviews. Learn More This article originally appeared in RECOIL Issue 39 Photos by Kenda Lenseigne Hi Power Redux, We Take Up Where JMB Left Off Back in the 1980s, if you wanted a 9mm handgun for serious purposes, your choices were severely limited. The Glock 17 had just been introduced and was still getting the side-eye from just about everyone, Beretta was cashing in the adoption of the 92 by the U.S. military, and everyone who tried CCW’ing one likened it to stuffing a fat chick into a Miata — and the S&W model 59 variants were OK, but DA/SA operation and slide-mounted safeties are not everyone’s cup of tea. Now, if you were a member of the cognoscenti there really was only one choice, the one which had been adopted by the armed forces of over 50 countries, the one gifted to the masses from the hands of the prophet John Moses (peace be upon him). The one, the only, GP35. The Hi Power isn’t without its faults. Its trigger isn’t the finest example of an interface between man and machine, it has an appetite for the flesh and blood of its user’s hand, and given its size, 13-round magazines aren’t all that and a bag of chips. Unfortunately, FNH froze development of the Hi Power with the introduction of the Mk3 version in 1988, and there’s a strong case to be made that nothing of great significance happened to the design from 1982 onward. With increased competition from polymer-framed, striker-fired handguns, sales slumped and parts production was halted in 2016, although the factory didn’t officially announce its death until two years later. Original gun is shown above, and wound up as you see here. Pretty isn’t she? With contrasting small parts against the most advanced PVD coating we could find, our Hi Power MkIV stands out in a sea of drab plastic. We were left to wonder what might have been, had FN continued to develop the pistol, rather than subject it to institutional indifference. After all, 1911s still have a cult following, and we can think of no one who carries the other iconic JMB pistol who elects to lug around an ’80s vintage version of that gun. Instead of just wondering about it, we chose to get off our arses and do something — as if we needed an excuse to start another gun project. There’s no denying the elegance of the basic design. Even ratty, old military examples of the Hi Power are more aesthetically pleasing than most striker-fired pistols today. It’s like comparing Lana Turner to Lena Dunham — not all progress is forward. Could we keep the features that attract us, while dressing the shortcomings? We’ll leave that to you, dear reader, to judge. Jodi Gritus took our beat-up sow’s ear and turned it into the silk purse you see on these pages. Follow her on Instagram @hipowerprincess. Our project started with a surplus Hi Power with FNH, rather than Browning rollmarks. Part of a consignment of Mk3 variants, which ended up in Israeli service in the late ’80s, it landed on these shores a few years ago and was snapped up for the first issue of CONCEALMENT, where it was featured in an article on bargain handguns. It had the usual Mk3 refinements, but also that model’s drawbacks: hammer bite, 12-pound trigger (yes, that’s not a misprint), smallish sights and, due to being dropped by some careless conscript, a big ding in the barrel crown. It was finished in epoxy, which was showing signs of abuse, and while still a very viable defensive handgun, it wasn’t one which inspired pride of ownership. Down to business. The first deficiency to be addressed was the lack of a beavertail. For those of us with man hands, the Hi Power hurts. Its hammer and frame tang combine to pinch the web between thumb and forefinger, and I can usually send about three rounds downrange before blood starts dripping. This has been a Hi Power feature since 1935, and there’s no reason it shouldn’t have been addressed from the get-go. To fix this chronic oversight, a chunk of steel is welded to the frame, then contoured and blended by hand until it looks like it came from the factory that way. Which it should have. To fix the gratuitously bad trigger pull (not all of them suck — I have a nickel Mk3 with a crisp, 5-pound break from the factory) a Cylinder and Slide sear and hammer were installed and tuned, along with a Wolfe spring kit. These were teamed with a Garthwaite flat trigger, which allows for better finger placement and feel, as well as a stronger trigger return spring to increase reliability. As a rule of thumb, anything inflicted on weapons design by the French government is a bad a thing, so our magazine safety was consigned to the scrap pile. These changes combined to make for a sweet, 4-pound trigger pull with about 1/8 inch of take-up, a short reset, and just a hint of overtravel. Custom guns are expensive, because just about every individual part is reworked by a fellow American who actually gives a sh*t about why they show up for work. Want to save a few bucks? Learn to do it yourself (which is something we wholeheartedly endorse), or send it to China. Oh, wait … The base gun arrived with an ambi safety, whose stock levers looked like dead slugs lying on the frame and weren’t too positive when it came to engagement. Unless you’re wrong-handed, ambidextrous safeties on a single-action carry gun are a mixed blessing and we’ve experienced several instances when a 1911 wound up with the safety disengaged due to the right-side lever catching clothing or bumping against car seats. It’s not too much of a contortion to reach around the beavertail with your thumb if you have to sweep it off left-handed, so we spec’d out a Cylinder and Slide extended version, which snicks into place with an air of quality. To complement the safety, we picked a C&S slide stop. It’s almost impossible to checker a Hi Power, as the front strap is paper thin and there’s an ever-present risk of cutting through into the magwell. In order to provide better traction, our ’smith stippled around the serial number, but before doing so she undercut the frame adjacent to the trigger guard, to allow a higher hold and greater control under recoil. The backstrap was treated to the same texturing, which was deliberately kept to the lower half so that the master hand could slide up under the beavertail without much friction, but once a firing grip was taken the pistol would stick like sh*t to an army blanket. Our surplus pistola appeared as if it had been carried by indifferent recruits, who likely used it as a convenient combination door stop and gardening implement, but shot it perhaps once every couple of years, so the barrel was in good shape internally. We elected to keep it, but have it recrowned. The chamber end was throated and polished to aid with feeding hollow-point bullets, which were carried in a pair of updated Mec Gar 15-round magazines. These are a big step up in quality from the standard, phosphated Mil-spec numbers, and allow for two more rounds, without increasing overall length. It was a no-brainer to swap out the original nylon grips for a pair of VZ’s palmswell G10 models, which were in keeping with the understated, professional look we were aiming for. Once all the gunsmithing work had been decided on, it was time to pick a finish. One advantage of polymer-framed guns is their resistance to corrosion — just don’t set them down too close to a fire — and we wanted something that would stand up to everyday carry. Traditional blueing, while attractive and fitting for a weapon designed in the 1930s, was considered then dismissed for practical reasons. As luck would have it, Robar was in the process of finishing up trials of a new surface treatment, which showed considerable promise. Lured by tales of its performance in salt spray tests, we signed on. Known as ArmorLube, it’s a specialist physical vapor deposition (PVD) process using a proprietary cocktail of exotic (and deadly) organic gases applied in a vacuum under high voltage. The result is very slippery, very hard, and available in any color, so long as it’s black. That beavertail took several hours of welding, grinding and finishing by hand. It could have shipped from the factory that way for a few pennies, but no. While the two-tone look was all the rage in the ’80s, we didn’t want to go to the extreme of a silver slide on a black frame. So for contrast we chose Robar’s NP3 plus, electroless nickel for small parts, such as the controls, extractor, and grip screws, due to its lubricity and corrosion resistance. The result is a nod to the Cocaine Cowboys era, while being relatively subtle and understated. So did we achieve the goal of dragging the Hi Power into the 21st century? Yes and no. Despite our best efforts, there’s still no place to mount a light, which would require a whole new frame, or a lot of machine work and welding. Everything else has been reworked to address weaknesses. Sights are first class, reliability has been improved, ergonomic problems with the original are addressed, and there’s a night-and-day difference in terms of trigger quality. We think it’s the gun FN should’ve been selling during the Bush administration — done at the factory in a production environment, economies of scale kick in, and the cost of improvements is driven down. When you sit on them, laurels just don’t last too long. Visit https://robarguns.com/ THE SMITH: JODI GRITUS RECOIL: What got you interested in gunsmithing? Jodi Gritus: I developed a love for firearms around the age of 18. I started out with some of the free programs at Ben Avery Shooting Facility. They taught the basics of safety and how to shoot pistols, rifles, and shotguns. A girlfriend and I were hooked on the sporting clays course for a while. My mom bought my first gun for my 19th birthday, a 12-gauge SKB pump shotgun. Anyway, I was working a boring, dead-end (customer service) job and wanted to find a steady, hands-on career. I searched courses for local community colleges and found out that Yavapai College had a gunsmithing program. That immediately sparked my interest. I told my husband about it, and he said that he wished he would’ve thought of it! Long story short, we both moved to Prescott, Arizona (from North Phoenix) for two years to attend YCC. I prefer to work with my hands and build something that I can take pride in, something that’s dependable enough for someone to trust with their life. I’m intrigued by the inner workings and function of firearms. I really enjoy running a machine, especially a manual mill. How did you get started? JG: The head instructor at Yavapai, Alan Lohr, had worked for Robar years prior. He referred both my husband, Jim, and I to Robar. We were very lucky to get hired for such a great, well-known company. My husband did rifle work mostly, and I was more geared to pistol smithing. The head gunsmith, Marty, started giving me lots of Hi Powers to work on. I was eventually deemed the “Hi Power Princess.” On a side note, I work on all kinds of pistols and am still learning about different firearms. What’s the biggest problem you face when dealing with customers? JG: It’s always tough when I have a project that’s only based on aesthetics … I cannot wrap my head around having a gun that looks gorgeous, but is unreliable. Also, people who don’t realize the completion date is an estimate. I very rarely work on something where I don’t come across additional issues that end up taking more time to fix. I treat each firearm as if it was my own, so I want it to leave here as perfect as it can be. Which project are you most proud of? JG: Gertrude. Gertrude is my FN Hi Power. I bought her from AimSurplus and she was a mess. I did a hi grip mod, beavertail, cut dovetails, and installed Novak tritium sights. I installed the C&S type II hammer (skeletonized), trigger pull reduction spring kit, C&S sear, match-grade sear lever, wide combat trigger, and extended slide stop. I stippled the front and backstrap. I also stippled a center line down the top of the slide and cut a border. She’s finished in NP3 complete with a matte to guard slide and VZ grips. She’s my favorite gun to shoot and probably always will be! Jodi Gritus’ FN Hi Power, Gertrude. Explore RECOILweb:LAG Tactical: Big Little Kydex MakerRECOILtv SHOT Show 2020: Spartan Precision Bipod SystemsFPS Russia - Saiga-12 Fully Auto (Video)New Zealand Selects LMT to Replace Steyr AUG NEXT STEP: Download Your Free Target Pack from RECOILFor years, RECOIL magazine has treated its readers to a full-size (sometimes full color!) shooting target tucked into each big issue. Now we've compiled over 50 of our most popular targets into this one digital PDF download. From handgun drills to AR-15 practice, these 50+ targets have you covered. Print off as many as you like (ammo not included). Get your pack of 50 Print-at-Home targets when you subscribe to the RECOIL email newsletter. We'll send you weekly updates on guns, gear, industry news, and special offers from leading manufacturers - your guide to the firearms lifestyle.You want this. Trust Us.
I don't care for hooked upswept beavertails. The short rowel spur "no bite" hammer from Cylinder & Slide should obviate any need for such things. And I say this as someone who loves the BHP. I currently have an Israeli police gun into which have been installed the C&S wide target trigger, tool steel sear, and no-bite rowel hammer. I sometimes think about getting tritium sights for it, but it is other than these mods, a polished feedramp--I did it myself by hand, no Dremel--and some nicely grippy G10 grips, stock. I wish the trigger reset weren't so far forward but otherwise it's a joy to shoot, black epoxy paint and all.
Jodi is awesome! I sent her my mid-80s built hi power when she was still at Robar a few years ago with a desire to turn it into the pistol I always wanted it to be. It was not very reliable, had absolutely god-awful sights, a horrendous trigger pull, etc., etc. After conversing back and forth a few times with emails to determine what my primarily goals were (100% reliability with all types of ammunition, accurate and a legacy build to hand down to one of my now grown children) I turned her loose to do whatever she felt needed done and wanted to do as long as the price did not exceed $2,000. If I remember correctly it came in under $1,700 at the end. She did a wonderful job and I was ecstatic when I received the gun back many months later and even happier after shooting it!! Not one single malfunction with any ammo I've run through it over the past few years and it's a thing of beauty! It is my EDC and the NP3+ finish Robar put on it is holding up quite well. It still looks the same as the day I got it back. I highly recommend her. She truly is the BHP Princess!!